Homemade jointer with an adjustable front table

Benchtop Jointer

In a homemade jointer, the front table with an adjustable working-surface height makes it possible to set the required chip thickness. And that means machining quality and productivity. In this machine design, the front table is raised or lowered in inclined guides by moving it with a lead screw.

This feature of the machine is built into the design of its bed, which consists of symmetrical halves welded from steel angles and joined by four pipes faced on a lathe. The bed height in the drawing corresponds to the benchtop version of the machine; for a floor-standing version, this dimension should be such that the working surface of the rear table is about 800 mm high.

Slots and holes for mounting the cutterhead bearing housings are made in the upper support surfaces of the bed.

Benchtop jointer
Benchtop jointer:
1 — bed; 2 — front table; 3 — cutterhead bearing housing; 4 — M8 stud (4 pcs.); 5 — rear table plate (steel, sheet 350x270x9); 6 — screw support base; 7 — screw support cover; 8 — cover plate (steel, sheet 190x45x3); 9 — side bar (steel, sheet 190x34x9); 10 — support plate (steel, sheet 260x190x9); 11 — shim (steel, sheet 190x30x1); 12 — front table travel screw; 13 — M10 screw (6 pcs.)

Mounting the front-table guides included welding the support plate and two side bars to the bed (all parts from 9 mm steel sheet), as well as the lead-screw support base and two shims.

The side bars were welded with the front-table guide plate present, using spacers, to guarantee clearances for its free movement later. The lead-screw support on the support plate and the nut on the front table were welded as an assembly with the lead screw.

Bed
Bed:
1,5 — support brackets (angle 50x50x5); 2,4 — frames (angle 50x50x5); 3 — spacer (tube 25×2, 4 pcs.)

The front table consists of upper and guide plates connected by two side pieces. The short sides of the plate are strictly parallel to each other and carefully finished. The side pieces were obtained by contour-machining two blanks clamped together. In the same stacked condition, 8 mm technological holes were drilled in the side pieces for temporary studs needed for assembling (welding) the front table. After the side pieces were welded to the upper and guide plates, the assembly studs were removed.

A few words about installing the cutterhead. The machine design allows the use of a cutterhead with a planing width of 200 and a cutting-part diameter of 80-110 mm.

Front table
Front table:
1 — upper plate (steel, sheet 300x270x9); 2 — guide plate (steel, sheet 192x45x9); 3 — side piece (steel, sheet 190x110x9, 2 pcs.); 4 — shaped M16 nut

The shaft assembly with the bearing housings was installed after some preliminary steps. The front table was raised to the cutterhead level and aligned with shims so that the beveled table edge and the shaft axis were parallel. After that, holes for fastening the cutterhead supports were marked and drilled in the bed.

The fixed rear table of the machine was adjusted for height and set parallel to the cutterhead using four M16 studs. For this, four slots were cut in the bed, and four holes for the threaded stud heads were drilled in the rear-table plate. By turning the corresponding nuts and moving the studs in the slots, the required clearance between the rear-table edge and the cutterhead can be obtained.

From the editors

Since there are clearances in the joint between the front table and the bed, vibration may appear. Therefore, it is useful to provide for locking the table relative to the bed. For example, with a bolt that passes through a threaded hole in the table guide plate and bears against the bed support plate.

“Modelist-Konstruktor” No. 2’2001, S. TYULYUMDZHIEV

Recommend to read

  • FULL KVADRFULL KVADR
    Introducing the ATV, our constant author S. Pletneva from the city of ocher, Perm territory. Once they built the machine indicative of the increased level of development and skills of...
  • WHEN THE BAR IS ROUNDWHEN THE BAR IS ROUND
    To cut a pipe or wood block round section diameter accurately is difficult. In this case, will help the jig from a wooden block having a groove, the width and height of the corresponding...