This model is very popular among French children: because making it requires merely a sheet of drawing paper with a size of 20X24 cm, divided into centimeter squares. The Central squares (see Fig.) bisect. 
Well in our time is no less important than before, especially given the popularity of cottage construction. No tap water, even filtered through modern filters can’t compare to well.
By its usefulness, well deserves to be the visible part of not just served a protective function, but also a decoration, served as a decorative design element of the site. For those who have your well, recommend the equipment of its ground part is not limited to a simple visor with a lid, and decorate a visor, for example, as shown in the photo. Pictured here the roof superstructure will be suitable for the existing well, and can serve and just his idea, a beautiful part of the area, if you are unable to acccess well.
Many rural Amateur designers rightly considered the most promising motoliberty tillage unit. However, it is not without drawbacks. And chief among them is the need every time to drag a heavy plow from the end of the furrow to the beginning, at the same time shifting the very motoliberty a distance equal Majboroda. The fact that in this case the power unit and tillers separated.
We present a prototype of the amphibious machine is a device hovercraft (Ohr) under the name “Aerodzhip”, publication of which was in the journal “modelist-Konstruktor” No. 7 for 2007. Like the previous machine, the new machine – a single-engine, single-rotor with distributed air flow. This model is also triple, with the location of the pilot and passengers at the T-scheme: pilot middle front, and passengers – on the sides, back. Although there is nothing stopping the fourth passenger to sit behind the driver – seat length and power rotor setup is enough.
My good friend since high school, enthusiastically collected stamps, matchbox labels, pocket calendars. Now his collection continues to children, and himself, he left only one passion: icons. And store came up with the original book, which makes itself as their collection. Material for their production is either thin cardboard or even paper.
Every time the whole family going on vacation, my task is to check the status of our bikes. As a rule, all the nodes are in order except for the tyres: they require periodic pumping. Here is sometimes hard, and much time is spent on it.
It was necessary to invent a device that would replace the pump. Its main components were borrowed from me… homemade siphon for aerating the water. The operation of the device is very simple. Carbon dioxide gets inside, it evaporates, creating a pressure that the tires necessary.
During the construction of the models is often necessary to apply a veneer of varying thickness. Typically the desired thickness is obtained by grinding with fungus with glued on end cloth, is inserted in the Chuck of the drilling machine. This method is most affordable, but it has several drawbacks: poor performance, inability to process veneer with thickness less than 0.5 mm, because of the rotation of the fungus veneer escapes from the hands and broken, and finally, the main drawback is the large air pollution wood dust. To handle more than three or four plates is not possible even a respirator.
I was lucky in my youth – got into the stream the student of camp life.
On the wave of rapid development among teachers mountain sport trips in our Kurgan machine-building Institute among students have formed groups more accessible pedestrian-“the plains” of tourism.
Within these new groups, which turned out to be and I bubbled its predpechatnaya social life. Everyone found a job interests and abilities. The head of the planned route. The caretaker was a list of products and estimated their cost. Sports organizer spent training and hikes of the day off. The girls wrote songs and was decorated by Gen. And I am a fan of tinkering, came up with a design: tents, windjackets, backpacks & bags camping equipment. Sewed them myself, and attracted to the work of other group members.
Any front panel aluminum alloy easy to decorative treatment. For example, after drilling holes in them you can first put these parts can be anodized, and then painted. Both processes require no special equipment and can easily be made at home.
A small panel anodize in a glass cuvette. It pour distilled water and add 200 ml of technical sulfuric acid for every 800 ml of water. The panel is clamped with the ends of the U-shaped brackets and dipped into the electrolyte. Above it, on hangers, a dural plate-electrode (this may be the second antirhea panel).
Large sibelectroterm plants from time to time organize specialized exhibitions, where to study avenues its primary products are making their drawings. Among other things come across the description and drawings of a variety of original furniture. This is done in order to interest the buyers in the acquisition of various tools and machines on the one hand and on the other to promote their products. These materials — is a convenient data sources for Amateur designers.
