DANCING SET

DANCING SET

The first impression when you look at this unusual furniture — it must be not very stable and probably too fragile, not intended to be familiar to such items load. Indeed, could it be reliable for, say, a table, whose each leg, bent, rests on the floor not in the place where it is traditionally supposed to be, and the place nearby, which, in turn, “leaves”, which is also in a strange position, and the last is first on scene? What kind of resistance, it would seem that the question if front be one leg front and… rear and rear — rear and one front…?

However, the original “dancer” furniture — not a hoax, not a joke design, but very real, which, moreover, by the conviction of the Hungarian magazine “Earmaster”, it is easy to make your own. If you look closely, it becomes clear that the fear of instability is only apparent. Judge for yourself. The fact that each leg rests on the floor not in his place, kompensiruet the fact that in its place rests the other, and the rest, as if in a circle, replace each other, forming the traditional “chetyreche-d”.

 
 
And despite the apparent singularity, this furniture is no harder to manufacture than traditional options similar items. The only difficulty is with the selection of material for the legs; it depends on the purpose of the subject, because in any case of load, for example, the stool is potentially greater than on the table. And this should be considered when making the legs. So consider that and other designs separately.
 
Table
 
It is not great dining, and easy; chess, cosmetic, or journal. For countertops in any of these three options will fit the sheet of plywood 12 mm thick. the size of the countertops is better to choose such that its edges overhung the base on all sides by approximately 50 mm.
 
More complicated, as already noted, the definition of the material for the legs. The ideal would be, of course, to cut them from solid wood boards (oak, beech) thickness of 20-25 mm, and then maybe their link to the capital bars wsip, with the formation of the under the sink kind of durable frame. But to find such boards with a size of 600×400 mm not less problematic.
Therefore, we consider a simplified version — with plywood or particle Board thickness 19 mm. In this case, they cut of the legs is better not to build in podstolny frame, and to make them applied separately to the assembled frame from bruskov by section 60×20 mm. the bars Themselves are connected round plug-in thorns with glue (carpenter’s, PVA), with the strengthening of the inside corners metal corners on the screws or triangular bars on the glue and screws.
 
Table and its basic details (on the mesh shown in three sizes)
Table and its basic details (on the mesh shown in three sizes):
 
1 — drawer side, forming podstolny frame; 2 – legs; 3 — tabletop.

 
From overhead the legs from the top, on the side facing to the frame, cut the ledge, equal to the height of the frame. To the frame legs are attached with glue and screws. The legs of the DSP, given the relative fragility of the material, prior to Assembly can be pasted as a strengthening plywood strips, repeating the configuration of the legs.
 
Stool
 
Technologically all of its elements and their connections same part of the table, except for the installation of the legs in the base. Given that there are on legs load is much higher than that of the table, two of them are mounted differently — not “vrazbezhku”, and towards each other, forming at the bottom of the crosshair And both pairs of legs are placed at the opposite sides of the corresponding bar podstolny frame. The thickness of the bar and the legs should be the same, and the ledges in the top part of the legs — vpoldereva, then the crosshairs will touch the legs and they can pull together for strength, screwed to the brace between the cross hairs of the legs. Thanks to this Assembly, the stool will gain the necessary strength.
Trim the legs of table and stool can be the same; this is a thorough polishing with emery cloth; processing stain, followed by varnish or paint enamels, nitro – or oil-based paints (the same with the bars of the underframes or frame of the seat).
 
Stool
Stool
 
1 — side-bar; 2 — legs vpoldereva; 3 — spacer; 4 —the screw of furniture.
 
options for the connection of the legs with tsargami
connection to the legs with tsargami:
 
A — hidden thorn; B — round plug-in thorns; In — vpoldereva.

 

Table tops and seats are, in principle, can be handled the same way. But there are better options. For example, if the pattern of wood countertops beautiful in itself, it is better after sanding to cover it with furniture or parquet lacquer in several layers with intermediate drying, which will further develop and enhance the natural beauty of the wood.
 
If the table is meant under potted plants, it is better to stick on the surface of the plastic sheet.
 
Simple plywood is easy to elevate with a sheet of veneer or solid squares of different colors beneath a “chessboard”.

 

Noticed mistape? Highlight it and press Ctrl+Enter, to inform us.

Recommend to read

  • TABLE ON TWO LEGSTABLE ON TWO LEGS
    it is Known: if the furniture is on legs, she's usually four, at least three. However, some items may be one Central pillar. But two is not found.   However — maybe two. For...
  • FURNITURE INVISIBLEFURNITURE INVISIBLE
    To create the greatest comfort and spaciousness in the room, especially in small apartments, it is possible to produce just such a "set" (Fig. 1), which I called "UNIVERSAL". It's enough...

Spelling error report

The following text will be sent to our editors: