The release of carbon dioxide industry miniature engines has caused many young technicians ‘ interest in the models in which you can use this reliable, silent, environmentally friendly motor. In the “M-K” have already talked about a few simple ship models with such engines. Today we offer you to make simple model airplane motor CO2. By construction, this classic high set scheme, made without the use of scarce balsa wood — mostly pine and light lime. The fuselage of the model are collected from pine spars a cross section of 2X2 mm and cross-beams of the same section. The Assembly is the simplest slipway, made of two sheets of plywood, covered with plastic wrap — so that the workpiece is not glued to the slipway. Build order is as follows: the rack-bars fixed with pins, then cut between the frame crossmember and finally the joints fill with epoxy glue so that between the blanks formed a fillet — a fillet transition. Billet spars are pre-bent over a candle flame. First, it makes sense to applied to the wall side of the fuselage, and then collect from half of spatial farm. Please note that the front spars of the fuselage together reinforced frame — lime plate thickness of 3 mm, it also serves as the basis for the engine mounts. The front part of the fuselage top and bottom (bottom to the rear edge of the wing and top to the front) paste over fake veneer thickness of 1 mm.INSTEAD OF FUEL – CO2
The release of carbon dioxide industry miniature engines has caused many young technicians ‘ interest in the models in which you can use this reliable, silent, environmentally friendly motor. In the “M-K” have already talked about a few simple ship models with such engines. Today we offer you to make simple model airplane motor CO2. By construction, this classic high set scheme, made without the use of scarce balsa wood — mostly pine and light lime. The fuselage of the model are collected from pine spars a cross section of 2X2 mm and cross-beams of the same section. The Assembly is the simplest slipway, made of two sheets of plywood, covered with plastic wrap — so that the workpiece is not glued to the slipway. Build order is as follows: the rack-bars fixed with pins, then cut between the frame crossmember and finally the joints fill with epoxy glue so that between the blanks formed a fillet — a fillet transition. Billet spars are pre-bent over a candle flame. First, it makes sense to applied to the wall side of the fuselage, and then collect from half of spatial farm. Please note that the front spars of the fuselage together reinforced frame — lime plate thickness of 3 mm, it also serves as the basis for the engine mounts. The front part of the fuselage top and bottom (bottom to the rear edge of the wing and top to the front) paste over fake veneer thickness of 1 mm.
Older homes still sometimes there are amazingly cozy and beautiful tiled stoves. Alas, today, like the furnace heating, the tiles are fading. And they can be found only as a piece of exhibits at exhibitions of ceramic artists. And whether it is, for lack of tiles to coat your kiln ceramic tiles? — often ask us readers. How to cook mastic to stick the tile to the furnace?
Many villagers and gardeners have on their sites shower. Usually this is a small free-standing enclosed building with a tank on the roof. From it by gravity through the pipe to the shower mesh enters the cold water. Of course, on a hot summer day, you can cool off in the cool streams, but in spring or autumn, when it’s fresh, not everyone will dare on such water treatment.
Everyone is used to what is required for forming the matrix and punch. In many cases, however, can do without the surround matrix — sufficient and shaped holes in sheet metal or plywood. But without the surround of the punch!..
Since 1980, the “geography” of the USSR Championships in the sport of flying remained the same — start small rockets passed on two “spaceports” (“Tapani” under Tbilisi and “Aranci” near Tashkent). But to VIII of the championship was selected the sports airfield “fakhrabad” Dushanbe ask.
Unremarkable externally, water tower farm “Precepts of Ilyich” Spassky district, Gorky region. One year supplies the sleep of the villagers spring water. However, coming closer, you will not hear the usual noise water pump operation — he’s not here! And although the source is considerably below the level of the top of the container, water, with only a short respite, rise up! It is not a miracle? No, just Gorky handyman, locksmith-Borsi Yiwu L. Ceranova managed to invent and test the original hydraulic installation, in which for lifting water is used… the energy of the source. We offer our readers acquainted with the principle of operation and device.
Fun and health that is unusual Playground, which introduces KDM today. All of her sports equipment and simulators can be made on their own from available materials.
An indispensable complement to modern homes steel built — in cabinets in the kitchen, hallway, bedroom. Unlike other types of furniture they do not take up useful floor space, simple and cheap to manufacture, and most importantly, being hidden in the wall, do not violate the rational solutions of the interior.