First the model of similar schemes appeared in the all-Union competition in 1982. With them were athletes from Moscow. But at the time of competition for soft raketoplana the type of wing”, Rogallo” they be not could. And further development of “hard” rocket gliders did not have. However, with the introduction in 1989 of a new category (S8 — rocket glider, which have not allowed separation of any elements of the design, including the engine block) this scheme has found a second birth in the category S4 (here design with soft wing is not allowed). In favour of the scheme say and world records set by V. Minakova and S. Ilyin, S. Ilyina at the training camp of the USSR team. The model we present to athletes rocketmodeler.THE REBIRTH OF THE “HARD” ROCKET PLANE
First the model of similar schemes appeared in the all-Union competition in 1982. With them were athletes from Moscow. But at the time of competition for soft raketoplana the type of wing”, Rogallo” they be not could. And further development of “hard” rocket gliders did not have. However, with the introduction in 1989 of a new category (S8 — rocket glider, which have not allowed separation of any elements of the design, including the engine block) this scheme has found a second birth in the category S4 (here design with soft wing is not allowed). In favour of the scheme say and world records set by V. Minakova and S. Ilyin, S. Ilyina at the training camp of the USSR team. The model we present to athletes rocketmodeler.
Reactive BM-8-24. In August 1941, took arms 82-mm rocket M-8. It was a modification of the aviation RS-82 for use in the field artillery, which had almost twice the mass of the explosive. Creating launchers for M-8 instructed SLE Moscow plant № 733 “Compressor” with the participation of the Bureau of plant No. 37. Led the development of V. A. Timofeyev, a leading designer of chassis D. I. Sazonov. In machine design engineers used a series of nodes from the BM-13, as well as guides such as “flute” used in aviation.
“Acquired motor brand Bouzid, going to use it on microstructure. But faced with the difficulties of linking the power transmission from the engine to the wheels, and the reversal of the movement, Maybe someone already solved this problem?”
For the fourth year keep the potatoes on the balcony in a container of foam slabs of size 900X 900X 90mm, strapped together by means of aluminum corners section 25×25 mm and length of 950 mm and steel pins ø 8 mm (Ø = 950 mm). At the ends of the studs is threaded M8. In places the joints are glued shopon thickness of 5-8 mm for sealing. The cover is pressed against the two lever locks and can be removed. Locks mounted on two metal bands spanning the box around the perimeter (Fig. 1).
The idea of building a jeep because we like an active holiday. The basis was taken of the legendary Soviet car UAZ-69. Since it was planned to overcome the car is not only cool roads, but long distances, over “UAZ” had to work hard. At first it was disassembled “to the last bolt” and reviewed.
If in the famous Guinness book of records recorded the simplicity and manufacturability, today we present to your attention a model would be the first contender for such a record. Especially attractive it is for young athletes. This model is a “bouzouki” with the engine working volume of 1.5 cm3. And all that will be needed for the manufacture of its frame, — a little more than five meters pine slats section 3X12 mm. They are easy to saw on the machine “Skillful hands”. The weight of the rails is about 100 G. Hence, with a relatively large wing area (dm2 21) it is easy to achieve a low specific loading and good maneuverability.
Not long ago I discovered, in his home workshop old Microdrive MK-12-In, preserved, apparently, since childhood. What to do with it? Throw a pity, and here decided though somehow to use.
When repairing thin lines (such as a car or refrigerator), it would be good to have on hand a small pipe cutter, and for connection of pipes with swivel nuts — device for rolling. Not hurt in a home workshop and a small vise. All of these devices can be made in the form of a set of interchangeable tool based on a simple clamp of suitable size (or specially manufactured). The design will need slight modification for mounting of tools for different purposes. In the first place must be milled afterwards the groove under all replacement fixtures (cage support rollers, rolling, vise) and drill a hole for the stopper.